Вот smartctl -a /dev/sda
[spoiler=Вот smartctl -a /dev/sda][root@comp-Celeron-D-1c01e9 ~]# smartctl -a /dev/sda
smartctl version 5.38 [i586-alt-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: MAXTOR STM3160215AS
Serial Number: 6RA5F86H
Firmware Version: 3.AAD
User Capacity: 160,040,803,840 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Mar 13 12:35:48 2010 KGT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 25) The self-test routine was aborted by
the host.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 54) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 114 076 006 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 097 097 020 Old_age Always - 3730
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 083 060 030 Pre-fail Always - 209101411
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 5727
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 097 097 020 Old_age Always - 3658
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 063 049 045 Old_age Always - 37 (Lifetime Min/Max 25/37)
194 Temperature_Celsius 0x0022 037 051 000 Old_age Always - 37 (0 16 0 0)
195 Hardware_ECC_Recovered 0x001a 095 057 000 Old_age Always - 99850550
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 198 000 Old_age Always - 525
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 152 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 152 occurred at disk power-on lifetime: 5371 hours (223 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 08 68 96 a1 e0 Error: IDNF 8 sectors at LBA = 0x00a19668 = 10589800
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 68 96 a1 e0 00 00:02:47.599 READ DMA EXT
25 00 08 60 96 a1 e0 00 00:02:47.600 READ DMA EXT
25 00 08 58 96 a1 e0 00 00:02:47.600 READ DMA EXT
25 00 06 52 96 a1 e0 00 00:02:47.600 READ DMA EXT
25 00 02 50 96 a1 e0 00 00:02:47.600 READ DMA EXT
Error 151 occurred at disk power-on lifetime: 5371 hours (223 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 08 68 96 a1 e0 Error: IDNF 8 sectors at LBA = 0x00a19668 = 10589800
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 68 96 a1 e0 00 00:02:37.438 READ DMA EXT
25 00 08 60 96 a1 e0 00 00:02:37.438 READ DMA EXT
25 00 08 58 96 a1 e0 00 00:02:37.438 READ DMA EXT
25 00 06 52 96 a1 e0 00 00:02:37.437 READ DMA EXT
25 00 02 50 96 a1 e0 00 00:02:37.437 READ DMA EXT
Error 150 occurred at disk power-on lifetime: 5371 hours (223 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 08 68 96 a1 e0 Error: IDNF 8 sectors at LBA = 0x00a19668 = 10589800
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 68 96 a1 e0 00 00:00:38.512 READ DMA EXT
25 00 08 60 96 a1 e0 00 00:00:38.512 READ DMA EXT
25 00 08 58 96 a1 e0 00 00:00:38.512 READ DMA EXT
25 00 06 52 96 a1 e0 00 00:00:38.512 READ DMA EXT
25 00 02 50 96 a1 e0 00 00:00:38.512 READ DMA EXT
Error 149 occurred at disk power-on lifetime: 5371 hours (223 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 08 68 96 a1 e0 Error: IDNF 8 sectors at LBA = 0x00a19668 = 10589800
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 68 96 a1 e0 00 00:00:31.762 READ DMA EXT
25 00 08 60 96 a1 e0 00 00:00:31.764 READ DMA EXT
25 00 08 58 96 a1 e0 00 00:00:31.764 READ DMA EXT
25 00 06 52 96 a1 e0 00 00:00:31.763 READ DMA EXT
25 00 02 50 96 a1 e0 00 00:00:31.763 READ DMA EXT
Error 148 occurred at disk power-on lifetime: 3245 hours (135 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 55 05 85 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x00850555 = 8717653
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 20 b6 67 44 e0 00 00:06:17.166 READ DMA EXT
25 00 01 00 00 00 e0 00 00:06:16.960 READ DMA EXT
25 00 80 be 0b 98 e0 00 00:06:16.947 READ DMA EXT
25 00 08 96 f1 6e e0 00 00:06:16.946 READ DMA EXT
25 00 40 d6 67 44 e0 00 00:06:16.939 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Aborted by host 90% 5727 -
# 2 Short offline Completed without error 00% 5727 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.[/spoiler]
[spoiler=hdparm]root@comp-Celeron-D-1c01e9 ~]# hdparm -I /dev/sda
/dev/sda:
ATA device, with non-removable media
Model Number: MAXTOR STM3160215AS
Serial Number: 6RA5F86H
Firmware Revision: 3.AAD
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312579695
device size with M = 1024*1024: 152626 MBytes
device size with M = 1000*1000: 160040 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Recommended acoustic management value: 208, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* SATA-I signaling speed (1.5Gb/s)
* SATA-II signaling speed (3.0Gb/s)
* Native Command Queueing (NCQ)
* Phy event counters
Device-initiated interface power management
* Software settings preservation
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct[/spoiler]
[spoiler=dmesg][root@comp-Celeron-D-1c01e9 ~]# dmesg | grep sda
[ 122.756755] sd 3:0:0:0: [sda] 312579695 512-byte logical blocks: (160 GB/149 GiB)
[ 122.775853] sd 3:0:0:0: [sda] Write Protect is off
[ 122.789767] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 122.789831] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 122.817732] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[ 122.888313] sd 3:0:0:0: [sda] Attached SCSI disk
[ 129.072652] Adding 1574360k swap on /dev/sda2. Priority:-1 extents:1 across:1574360k
[ 129.450011] EXT3 FS on sda3, internal journal[/spoiler]
Проверка smartctl -t short /dev/sda или smartctl -t long /dev/sda
заканчивается одинаково Use smartctl -X to abort test
Слов нет, буду курить маны. 